Sweet N' Cute Creations

Amigurumi Sir Miniopoly Pattern

please dont forget to like my fb page too :D http://fb.com/sweetncutecreations

Materials

4ply acrylic yarn

hook G

tapestry needle

rubber tubing

hard plastic

fiberfill stuffin

safety eyes

telephone cord

glue gun

Head/body

using yellow
R1: ch 2, 5 sc in 2^nd ch from hook
R2: 2 sc in each st around
R3: *sc in next st, 2 sc in st after* repeat until the end of the round
R4: *sc in each of the next 2 sts, 2 sc in st after* repeat until the end of the row
R5: *sc in each of the next 3 sts, 2 sc in st after* repeat until the end of the row
R6-18: sc all around
R19: sc all around [15 black, 5 white, 15 black]
R20: sc all around [16 black, 3 white, 16 black]
R21: sc all around [17 black, 1 white, 17 black] 
using black
R22: sc all around
R23: *sc in each of the next 3 sts, sc2tog in next* repeat until end of the row.
start sewing on the mustache and mouth here. attach the two eyes as well. make sure the eyes are equidistant from each other and from the mouth. sew on a mini tie using red acrylic yarn too. in sewing a tie, it’s just making an upside down triangle :D the tip of it will be where there’s only 1 white stitch.
R24: *sc in each of the next 2 sts, sc2tog in next* repeat until end of the row
R25: *sc in next st, sc2tog in next* repeat until end of the row
R26: sc in every other st

Hat

using black

R1: ch 2, 5 sc in 2^nd ch from hook
R2: 2 sc in each st around
R3: *sc in next st, 2 sc in st after* repeat until the end of the round
R4: *sc in each of the next 2 sts, 2 sc in st after* repeat until the end of the row

R5: through back loops only, *sc in next st, 2sc in st after* 

Arms

using yellow

R1: ch 4, 5 sc in 2^nd ch from hook
R2: 2 sc in each st around
R3: sc all around

using black

R4: through front loops, sc all around
R5-8: sc all around 

Legs

R1: ch 2, 6 sc in 2^nd ch from hook
R2: 2 sc in each st around
R3: *sc in next st, 2 sc in st after* repeat until the end of the round
R4: through back loops, sc all around
R5-8: sc all around

HOW TO MAKE THE MONOCLE

get a rubber tube, cut approximately 5mm of it or even less. get a hard piece of plastic [this can be gotten from any microwavable case] and cut it into a circle just a little bigger than your rubber tube. make sure that the rubber tube fits snuggly on the eye…it can be a little bit bigger but not too big :D. finally, using a glue gun, just pour an ample amount of it around the rubber tubing and out the hard plastic on top, once it’s secure, put some double sided tape on the end without the glass. do not remove the double sided tape yet!

HOW TO MAKE THE CANE

get a very flexible used telephone cord. curve it to look like a cane. cut it to fit the minion :D

ASSEMBLY

1.  lightly stuff the “top hat” then sew it onto the top of the head
2. sew on the cane to the hand part of the arm
3. Stuff the arms and sew it onto the body…make sure that it is proportional to the entire minion. i put mine from the start of where i had black stitches
4. Stuff the entire body/head
5. close the ends of the body/head
6. sew on the legs to the body
7. take out the double sided tape’s cover from the monocle’s bottom part and attach it to the eye
8. there you have it, your very own little sir miniopoly to help you dominate the world…like a sir!